Just how to Install a Bathtub ( Guide).
Just how to Install a Bathtub ( Guide).
Blog Article
This article following next on the subject of How to Install a Bathtub is amazingly insightful. Give it a go and draw your own final thoughts.
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also often, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily available, the task can move immediately; if you need to open a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit attempting it. Instead of working with a service provider to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will aid you install a new tub in your shower room if you have actually currently acquired a new tub and don't need to alter the arrangement of your previous water system pipelines.
Your devices and also product list need to comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our topic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking time to read our short article. Are you aware of another person who is in the market for the niche? Please feel free to promote it. Thanks a lot for your time. Visit us again soon.
Schedule Today! Report this page